Posté le: Lun Juin 30, 2008 8:54 pm Sujet du message: Double boot ??!! Cisco 1721
Bonjour,
Le boulot m'a donné mon 1er cisco (1721) qui avait bien 2 ans de poussiere
Donc, je l'ai mis à zero et je farfouille dedans depuis quelques jours seulement - même pas une semaine.
Mon soucis de double-boot est probablement bete à manger du foin mais il y a quelque chose dans ma config que je dois faire de travers.
Les habitués verront surement pleins d'erreurs dans les confs réseaux qui vont leur crever les yeux, mais je tiens à les trouver puis résoudre comme un grand Google is our friend.
De plus, je n'ai pas l'adsl chez moi, donc pas évident à les imaginer ces erreurs, mais c'est un autre soucis (pas d'authentification FAI de configuré par ex).
Citation:
System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 49152 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x623244
Self decompressing the image : ########################################################################################################################################################################################################################################################################### [OK]
%DIALER-6-BIND: Interface Vi1 bound to profile Di0
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
program load complete, entry point: 0x80008000, size: 0x623244
Self decompressing the image : ########################################################################################################################################################################################################################################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SY7-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 11-Apr-02 21:45 by ealyon
Image text-base: 0x80008124, data-base: 0x80B23970
cisco 1720 (MPC860T) processor (revision 0x501) with 36864K/12288K bytes of memory.
Processor board ID JAD04450D4V (816173112), with hardware revision 0000
MPC860T processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
1 ATM network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
00:00:04: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
00:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
00:00:10: %LINK-3-UPDOWN: Interface ATM0, changed state to down
00:00:11: %LINK-5-CHANGED: Interface BRI0, changed state to administratively down
00:00:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
00:00:11: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
00:00:12: %SYS-5-CONFIG_I: Configured from memory by console
00:00:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, changed state to down
00:00:14: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SY7-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 11-Apr-02 21:45 by ealyon
00:00:14: %SNMP-5-COLDSTART: SNMP agent on host Router1 is undergoing a cold start Tu entres sur un systeme securise, acces authorises SEULEMENT !
Router1>
Une vision de ma version de config.
Citation:
sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SY7-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 11-Apr-02 21:45 by ealyon
Image text-base: 0x80008124, data-base: 0x80B23970
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SY7-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router1 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:V1224YA2.PAO"
cisco 1720 (MPC860T) processor (revision 0x501) with 36864K/12288K bytes of memory.
Processor board ID JAD04450D4V (816173112), with hardware revision 0000
MPC860T processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
1 ATM network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router1#
Et bien-sûr, ma config (mdp masqués).
Attention les yeux
Citation:
sh run
Building configuration...
Current configuration : 2108 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Router1
!
boot system flash V1224YA2.PAO
enable secret 5 password.
enable password 7 password
!
memory-size iomem 25
clock timezone PARIS 1
ip subnet-zero
!
!
ip name-server 208.67.222.222
ip name-server 208.67.220.220
!
ip dhcp pool TitouLAN
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 208.67.220.220
lease 5
!
vpdn enable
!
vpdn-template
!
!
!
!
interface ATM0
description Patte WAN
no ip address
no ip mroute-cache
no atm ilmi-keepalive
pvc 8/35
ubr 160
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
dsl operating-mode auto
!
interface BRI0
no ip address
no ip mroute-cache
shutdown
!
interface FastEthernet0
description Patte LAN
ip address 192.168.100.1 255.255.255.0
ip nat inside
no ip mroute-cache
speed auto
full-duplex
!
interface Dialer0
ip address negotiated
ip access-group 103 in
ip nat outside
encapsulation ppp
dialer pool 1
ipv6 enable
ipv6 traffic-filter fw-in in
no ipv6 nd suppress-ra
no cdp enable
ppp authentication chap pap callin
!
ip nat inside source list 10 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip http server
ip http access-class 1
ip pim bidir-enable
!
!
access-list 1 permit 192.168.100.0 0.0.0.255
access-list 1 deny any log
access-list 10 permit 192.168.100.0 0.0.0.255
!
snmp-server community public RO
banner login ^CINE
TTTTTTTTTTT III TTTTTTTTTTT OOOOOOOOOOO UUU UUU
TTT TTT OOO OOO UUU UUU
TTT III TTT OOO OOO UUU UUU
TTT III TTT OOO OOO UUU UUU
TTT III TTT OOO OOO UUU UUU
TTT III TTT OOO OOO UUU UUU
TTT III TTT OOO OOO UUU UUU
TTT III TTT OOOOOOOOOOO UUUUUUUUUUU^C
banner motd ^C Tu entres sur un systeme securise, acces authorises SEULEMENT ! ^C
!
line con 0
line aux 0
line vty 0 4
password 7 mdptelnet
login
!
end
Router1#
J'avais pensé à retirer cette ligne
Citation:
boot system flash V1224YA2.PAO
mais j'ai peur que le routeur ne se lance plus si je l'enleve...
Inscrit le: 16 Juil 2008 Messages: 11 Localisation: France
Posté le: Jeu Juil 17, 2008 12:00 pm Sujet du message:
Tout a fait Titou93, tu peux l'enlever, elle est utile si tu as plusieur image (IOS), et qut tu préfére booter sur l'une ou l'autre, grâce à cette commande tu peux préciser celle que tu veux utiliser.
Mais vue que tu n'as qu'un seul IOS, elle n'est pas utile.
Vous ne pouvez pas poster de nouveaux sujets dans ce forum Vous ne pouvez pas répondre aux sujets dans ce forum Vous ne pouvez pas éditer vos messages dans ce forum Vous ne pouvez pas supprimer vos messages dans ce forum Vous ne pouvez pas voter dans les sondages de ce forum